Category Archives: E-Type Component Restoration

This blog highlights some of the individual components that customers have sent in to have restored in our shop. Browse through the work and see if we can help with YOUR E-Type!

Series 2 E-Type Bonnet – LH Inner Valance

Posted on August 15, 2016 by admin

This is the restoration of a Series 2 LH Inner Valance that is actually more of a rare piece, since it is an original from a NON-AC Series 2 bonnet. Late Series 1 cars have the same Air-conditioning setup as … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on Series 2 E-Type Bonnet – LH Inner Valance

E-Type Bonnets – Restore or Replace?

Posted on August 13, 2016 by admin

Hello! Honestly – it has been so long since I wrote a blog entry, for a minute I forgot how to get started!  Sorry guys – work and life has been very busy, and as the business continues to grow, … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration, E-Type Custom Panel Fabrication | Comments Off on E-Type Bonnets – Restore or Replace?

Series 2 E-Type Lower Valance Restoration

Posted on April 23, 2016 by admin

We’re busy as usual, so I am going to have to skip the captions on this blog, but here are some photos of a Series 2 lower valance that we recently restored. This is part of a Series 2 bonnet … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on Series 2 E-Type Lower Valance Restoration

Converting a Series 2 wing to Series 1

Posted on December 13, 2015 by admin

Before we show more of the whole “new shop” thing, let’s get back to some metalworking, shall we? By the way – this work was done in the NEW shop – check out how clean and nice the bench is!  … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type - Covered Headlamp Conversion, E-Type Component Restoration, E-Type Custom Panel Fabrication | Comments Off on Converting a Series 2 wing to Series 1

E-Type Series 1.5 Bonnet Lower Valance Repairs

Posted on June 25, 2015 by admin

Next Up for this bonnet was the restoration of the lower valance.  We have done ALOT of these, and blogged it many times as well, so I’m going to try to keep the captions short on this one and get … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on E-Type Series 1.5 Bonnet Lower Valance Repairs

E-Type Series 1.5 Bonnet Inner Valance Repairs

Posted on June 25, 2015 by admin

Well, it happens – and it’s been a while – so I guess I was “due” to hurt myself, and did a first class job of it yesterday afternoon… I was drilling out ONE spot weld in the middle flange … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on E-Type Series 1.5 Bonnet Inner Valance Repairs

Series 1 E-Type Bonnet Center Section Repairs

Posted on March 17, 2015 by admin

The ’66 FHC project that we recently sold had a pretty tired bonnet, and while the new owner was willing to jump in and tackle the panel replacement of the monocoque shell itself, he was concerned that he did not … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on Series 1 E-Type Bonnet Center Section Repairs

E-Type “Doo-Dads!”

Posted on January 22, 2015 by admin

Over time, things just kind of “accumulate” here…  It’s kind of weird, actually – it’s almost like the stuff just “grows” sometimes!  I do buy alot of stuff, and that is of course one way that it accumulates, but some … Continue reading →

Posted in - All Blog Posts -, E-Type Adventures!, E-Type Component Restoration | Comments Off on E-Type “Doo-Dads!”

1961 Jaguar E-Type FHC #43 – Rear Hatch Drip Channel

Posted on January 11, 2015 by admin

If you look closely at the photos, you can see that based on what is going on in the background, this E-Type has been underway for a while now… There are alot of reasons for that – it’s been busy … Continue reading →

Posted in - All Blog Posts -, 1961 Fixed-Head Coupe #43 - JM, E-Type Component Restoration, E-Type Custom Panel Fabrication | Comments Off on 1961 Jaguar E-Type FHC #43 – Rear Hatch Drip Channel

1961 Jaguar E-Type FHC #43 – Priming the Shell

Posted on January 10, 2015 by admin

We eventually got to a point with the shell (and the weather…), where we just couldn’t wait any longer to get some good primer on the shell. We have switched over from self-etching primer to epoxy primer.  It is a … Continue reading →

Posted in - All Blog Posts -, 1961 Fixed-Head Coupe #43 - JM, E-Type Component Restoration | Comments Off on 1961 Jaguar E-Type FHC #43 – Priming the Shell

Series 1 E-Type Bonnet Project – Part 2 – Assembly & Primer

Posted on December 30, 2014 by admin

In the second half of this blog entry, you’ll see photos of what the finished product from Monocoque Metalworks looks like. In my somewhat biased opinion, you simply cannot have a bonnet better than what is shown in these photos … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on Series 1 E-Type Bonnet Project – Part 2 – Assembly & Primer

Series 1 E-Type Bonnet Project – Part 1 – Metalwork

Posted on December 30, 2014 by admin

These are photos of yet another Series 1 bonnet that was restored here this Fall. This bonnet was a very good representation of an “average” original bonnet being restored – it had some accident damage and some rust – all … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on Series 1 E-Type Bonnet Project – Part 1 – Metalwork

Series 1.5 E-Type Bonnet Repair & Headlamp Conversion

Posted on December 30, 2014 by admin

As I mentioned earlier, we restored several bonnets this Fall in our effort to “clear the decks” and prepare to be locked in for the Winter restoring body shells. This bonnet was completed in November.  The owner was a long-time … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type - Covered Headlamp Conversion, E-Type Component Restoration, E-Type Custom Panel Fabrication | Comments Off on Series 1.5 E-Type Bonnet Repair & Headlamp Conversion

E-Type Bonnet Side Flange Repair

Posted on December 6, 2014 by admin

Fall was the season of bonnets around here – we cranked out FOUR complete bonnet restorations in October and November among the other work going on – that’s alot of bonnets in a short time! This particular bonnet was a … Continue reading →

Posted in - All Blog Posts -, E-Type - Bonnet Restoration, E-Type Component Restoration | Comments Off on E-Type Bonnet Side Flange Repair

Holiday Doorbuster!

Posted on November 23, 2014 by admin

You hear the word “Doorbuster” this time of year referring to all of the Black Friday sales, etc. Around here last week, it meant a little something different…

Posted in - All Blog Posts -, E-Type - Doors, E-Type Component Restoration | Comments Off on Holiday Doorbuster!